The Gas Extinguishing System offers outstanding value and performance for all small to medium fixed firefighting installations.

We supply all UL Listed and FM Approved components. The system is complete with Gas extinguishing control panels, detectors, audio visual equipment and activation devices.

FEATURES

• Zero Time delay upon manual release
• Single or Any combination of zones can be configured
• Easy access to terminals
• Countdown timer to show time remaining until release
• 360° view of detection devices
• Low Standby Current
• Both Audio and Visual notification devices
• All types of detection capabilities

We have designed and supplied plenty extinguishing systems and suppression system based on inert gas and clean agent gas. We understand the importance of the Gas extinguishing system with detection and activation.

We choose the best among the available solutions in the market and design your system to the best capabilities to provide the efficient and eminent fire protection against hazards.

The Gas Extinguishing systems components include:

• Gas Extinguishing Control Panel
• Ancillary PCB
• Lamp Status Indicators
• Manual Pull Station
• Abort Switch
• Conventional Fire Alarm Bell
• Audio Visual Signal Indicator
• Heat Detector
• Photo-electric Smoke Detector
• Multi Criteria Detector
• Conventional Detector Bases

Conventional Fire Alarm Systems are traditionally used as an early warning system for fire hazards in smaller locations. These systems would give you an alarm when fire is detected, but they can only guide you to the zone where the fire hazard is located. They cannot point you to the exact location of the hazard.

Conventional systems are also sometimes called ‘dumb’ systems, purely because they cannot provide any detailed information and also do not provide any network output. But in small buildings, this is not a concern and hence the Conventional Fire Alarm system is the perfect choice for such projects.

SFFECO as a fire fighting products specialist with over 30+ years of project experience has had the chance of supplying and designing infinite small to medium project where the use of Conventional Fire Alarm is vital.

Many a times, we have successfully designed the complete fire alarm system by suggesting conventional fire alarm systems instead of addressable systems, as it was more practical and apt for the specific project.

The Conventional Fire Alarm systems are inexpensive and easy to install, but also hard to maintain as each unit in the system has to be manually checked for service.

The Conventional Alarm systems components include:

• 1 Zone Fire Alarm Control Panel
• 2 Zone Fire Alarm Control Panel
• 4 Zone Fire Alarm Control Panel
• 6 Zone Fire Alarm Control Panel
• 8 Zone Fire Alarm Control Panel
• 12 Zone Fire Alarm Control Panel
• 16 Zone Fire Alarm Control Panel
• Photo-electric Smoke detector
• Heat Detector
• Siren with Strobe
• Sounder Beacon
• Audio Visual Sounder
• Conventional Fire Alarm Bell
• LED Remote Indicator
• Manual Call Point
• Gas Extinguishing Panel

Addressable systems work on the concept of unique addresses for each device connected in the network. Each call point or detector in the network is connected in loops which can be easily addressed using the control panel of the addressable fire alarm system.

These systems are different from Conventional system as they point out the exact device that is being alarmed and not just the zone unlike the conventional systems.
This can save time and also help in rapid action in situations of fire.

SFFECO has supplied and designed numerous projects in various industrial and commercial sectors. With experience we have become experts in designing and implementing Addressable Fire Alarm Systems in simple to complex projects, resulting in proper detection and protection against fire.

The KM approved Addressable Fire Alarm System has been designed as a simple to use and install for any kind of requirements.

The KM Approved systems we use are available in 1 Loop, 2 loops and 4 loops, and each loop can have upto 127 devices.

The system components include.

• 1  Loop Fire Alarm Control Panel
• 2 Loop Fire Alarm Control Panel
• 4 Loop Fire Alarm Control Panel
• Intelligent Photo-electric Smoke Detector
• Intelligent Heat Detector
• Intelligent Smoke & Heat Detector
• Intelligent UV Flame Detector
• Detector Isolating Base
• Addressable Manual Call Point
• Audible and Visual Alarm Indicator
• Signal Input Module
• Relay Output Module
• Short Circuit Isolator
• Conventional Zone Interface
• Remote Control Module
• Addressable Programmer
• Repeater Panel

Addressable systems work on the concept of unique addresses for each device connected in the network. Each call point or detector in the network is connected in loops which can be easily addressed using the control panel of the addressable fire alarm system.

These systems are different from Conventional system as they point out the exact device that is being alarmed and not just the zone unlike the conventional systems.
This can save time and also help in rapid action in situations of fire.

SFFECO is proud to state that we have more than 3 decades of experience in successfully designing and implementing addressable alarm systems in complex projects.

We supply UL Listed Addressable Alarm systems, which are at the top of the industry standards and are hence more reliable to protect your projects.

The systems we use are available in 2 loops and 4 loops, and each loop can have more than 120 devices in any required combination.

The system components include.

• 2 Loop Fire Alarm Control Panel
• 4 Loop Fire Alarm Control Panel
• Serial LCD Annunciator
• LCD Network Annunciator
• Photoelectric Smoke Detector
• Heat Detector
• Multi-criteria Detector
• Analog Sounder Base
• Analog Detector Base
• Conventional Detectors
• Duct Detectors
• Fast Response Contact Module
• Dual Relay Output Module
• Supervised Output Module
• Key Switch Disable Module
• Dual Input Monitoring Module
• Conventional Zone Module
• Short Circuit isolator
• Manual Pull Station
• Fire Alarm Bell
• Evacuation Signals
• Projected Beam Smoke Detector

Emergency Bulk Heads – The traditional, functional, weatherproof and low energy consuming way of giving emergency lights in the required zones.

These bulk heads help in identifying the exit route during calamities. They are the most common emergency lighting available and are hence normally used in all kinds of buildings.

The Emergency Bulk heads are low voltage and a battery backup of upto 3 hours after charge. The battery has a long life of upto 4 years.

The Dual Head Emergency Lights is a stylish light that is very easy and simple to install. The design finish is very good and hence it fits any kind of decor, specially with the 2 neutral colors available in White and Black.

The model comes with two completely adjustable lighting heads that ensure that your light can be directed to the required areas easily. This is one feature along with the easy installation, that makes the Dual Head Emergency Light a very fast moving product.

The Emergency lights are low voltage and a battery backup of upto 3 hours after charge. The battery has a long life of upto 4 years.

Our LED Emergency Exit Light features a housing that is impact resistant, scratch resistant and corrosion proof. With the new advanced  features and industry-leading innovations, the exit signs now consume less energy, and are universal in design and hence can be placed at any kind of exit gates.

Our lights come with single faced configuration and double faced configuration. These exits signs have replaceable directional arrow inserts for easy re-inserting in the required directions.

The Emergency Exit signs are low voltage and a battery backup of upto 3 hours after charge. The battery has a long life of upto 4 years.

Our LED Combination Emergency and Exit Light come with a very unique low profile design, which allows them to be fixed and mounted above exit gates and also in restricted spaces.

Our lights come with single faced configuration and double faced configuration. These LED Lights provide the function of Exit Signage and Exit Lighting in just one single unit.

The LED Combination Emergency and Exit Light  are low voltage and a battery backup of upto 3 hours after charge. The battery has a long life of upto 4 years.